IMPORTANT: Do Not Return Dispenser to Store. If you have questions or issues please contact 1-866-429-7566 for expert assistance.
Home Series
Bottom Loading
Water Dispensers
TO REDUCE THE RISK OF INJURY
AND PROPERTY DAMAGE, USER
MUST READ THIS MANUAL
BEFORE ASSEMBLING, INSTALLING
& OPERATING DISPENSER.
SAVE THIS MANUAL
FOR FUTURE USE
This Home Series water dispenser has been designed and manufactured to
provide dependable and safe service if installed, set up, operated and
maintained as directed. Follow all instructions in the order provided.
No tools or hardware required.
Locate Dispenser
Notice: Do NOT plug power cord into wall outlet until instructed.
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded location near
a ground fault interrupting receptacle.
3. Position dispenser so the back is at least 4 inches from wall and there are
at least 4 inches of clearance on both sides.
Install Drip Tray & Grid
1. Remove drip tray and grid from protective
2. Slide drip tray assembly into position until it
Install Water Bottle
Bottle not included. Requires standard 3, 4 or 5
gallon water dispenser bottles.
Visit www.PrimoWater.com to find Primo
Water at a store near you.
1. Clean bottle cap and neck with a cloth and
warm soapy water, then rinse.
2. Open dispenser door.
3. Place probe assembly on probe hanger.
4. Place fresh bottle outside of cabinet.
5. Remove entire plastic cap from top of bottle.
6. Clean outside of new bottle with a cloth.
7. Place probe into bottle.
8. Slide collar down until it clicks in place.
FEATURES & FUNCTIONS
Water Dispensing Controls – Depress to dispense.
Function Lights – Green light below ON icon indicates the dispenser is
plugged in. Green light below snowflake indicates the dispenser is cooling
water. Green light below wavy lines indicates the dispenser is heating
water. Blinking red light below the bottle icon indicates the bottle is
Spout(s) – Amount vary by model. Water dispenses here.
Bottle Support(s) (Not on All Models) - Helps align sports bottles and
glasses with spout(s) to eliminate spills.
LED Nightlight (Not on All Models) – Located behind bottle support(s).
Helps in low light situations.
Drip Tray – Dishwasher safe. Slides in and out. Red float rises to top to
inform you it is time to empty the tray.
Probe Assembly – Located inside cabinet. Connects to bottle to allow
water to be pumped into tanks for heating and cooling.
Probe Hanger – Located inside door at top. To keep probe assembly clean
when changing bottles, rest it here.
Activation Switch for Cooling – Green
10 Activation Switch for Heating – Red (Not on All Models)
11 Activation Switch for LED Nightlight – Blue (Not on All Models)
12 Hot Tank Drain – Use when cleaning. Caution: Water can flow at
extremely high temperatures. Failure to use properly can cause personal
13 Plug & Cord –Only plug into a ground fault interrupting receptacle.
9. Push head down until tube hits bottom of bottle.
10. Slide bottle into cabinet and close door. Notice: Water will not pump from
bottle unless door is fully closed.
Provide Electricity
Plug cord into a ground fault interrupting receptacle. At this time the pump will
begin to move water from the bottle to the hot and cold tanks. It will take up to
12 minutes to fill the tanks for the first time. During this period the pump will run
continuously. This is normal.
Activate Cold Switch
Notice: This unit will not dispense cold water until the switch is activated.
To activate, push top side of the green switch in to start cooling water. If you do
not want cold water leave switch in off position – bottom side pushed in.
Activate Hot Switch
Notice: This unit will not dispense hot water until the switch is activated.
To activate, push top side of the red switch in to start heating water. If you do not
want hot water leave switch in off position – bottom side pushed in.
Activate Nightlight (Not on All Models)
To activate, push top side of the blue switch in. The LED bulb behind center spout
will light. If you do not want a nightlight leave switch in off position – bottom side
Register at Club Primo
While you wait for the water to get to the desired temperatures, please register
your dispenser. This will be helpful should you need customer service assistance in
the future. Go to www.PrimoWater.com and click on Club Primo.
This Home Series water dispenser has been tested and sanitized prior to packing
and shipping. During transit dust and odors can accumulate in the tank and lines.
Dispense and dispose at least one quart of water prior to drinking any water.
Join Club Primo at PrimoWater.com for more useful information, instructional videos, tips and special offers.
WARNINGS & SAFETY PRECAUTIONS
To reduce risk of injury and property damage, user must
read this entire guide before assembling, installing &
operating dispenser.
Failure to execute the instructions in this manual can
cause personal injury or property damage.
Models that heat water dispense at very high
temperatures. Failure to use properly can cause
personal injury.
When operating this dispenser, always exercise basic
safety precautions, including the following:
Prior to use, this dispenser must be properly assembled and installed in
accordance with this manual.
This dispenser is intended for water dispensing only. Do NOT use other
liquids. Do NOT use for other purposes. Never use any other liquid in the
dispenser other than known and microbiologically safe bottled water.
For indoor use only. Keep water dispenser in a dry place away from direct
sunlight. Do NOT use outdoors.
Install and use only on a hard, flat and level surface.
Do NOT place dispenser into an enclosed space or cabinet.
Do NOT operate dispenser in the presence of explosive fumes.
Position back of dispenser no closer than 4 inches from wall and permit free
airflow between wall and dispenser. There must be at least 4 inches
clearance on the sides of the dispenser to permit airflow.
The dispenser is intended to be plugged into a ground fault interrupting
receptacle.
Do not use an extension cord with your water dispenser.
Always grasp plug and pull straight out from outlet. Never unplug by pulling
on power cord.
Do NOT use dispenser if cord becomes frayed or otherwise damaged.
To protect against electric shock, do NOT immerse cord, plug, or any other
part of dispenser in water or other liquids.
Ensure dispenser is unplugged prior to cleaning.
Never allow children to dispense hot water without proper and direct
supervision. Unplug unit to prevent unsupervised use by children.
Do not dispense hot water if water bottle is empty.
Service should be performed only by a certified technician. Please contact us
at 866-429-7566 for assistance.
Dispensing Cold Water
After setup, it will take 1 hour to get water to maximum cold temperature.
During this time the compressor will run continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control (dark blue) downward to start water flow.
3. Release control once desired fill level is achieved.
Dispensing Cool Water (Not on All Models)
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cool water control (light blue) downward to start water flow.
3. Release control once desired fill level is achieved.
Dispensing Hot Water
CAUTION: This unit dispenses water at temperatures that can cause severe
burns. Avoid direct contact with hot water. Keep children and pets away
from unit while dispensing. Never allow children to dispense hot water
without proper and direct supervision. Unplug unit to prevent unsupervised
use by children.
After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Slide red button away from you and depress control downward to
start water flow.
3. Release control once desired fill level is achieved.
MAINTENANCE
For best taste, performance and hygiene, clean the cold tank at least every 3
months and your cabinet, controls, probe and spout each time you change your
water bottle. Empty and clean drip tray as needed. To minimize mineral
deposits, use only high quality purified bottled water such as Primo.
For instructions and videos for maintaining your dispenser please visit -
http://store.primowater.com/SpecialPages/CustomerCare.aspx#
LIMITED WARRANTY
Primo Water Corporation, ("Vendor") warrants to the original purchaser of this
dispenser, and to no other person, that if this dispenser is assembled and
operated in accordance with the printed instructions accompanying it, then for
a period of one (1) year from the date of purchase, all parts in such dispenser
shall be free from defects in material and workmanship. Vendor may require
reasonable proof of your date of purchase from an authorized retailer or
distributor. Therefore, you should retain your sales slip or invoice. The Limited
Warranty shall be limited to repair or replacement of parts, which prove
defective under normal use and service and which Vendor shall determine in
its reasonable discretion upon examination to be defective. Before returning
any parts, you should contact Vendor's Customer Care Department using the
contact information listed below. If Vendor confirms, after examination, a
defect covered by this Limited Warranty in any returned part, and if Vendor
approves claim, Vendor will replace such defective part without charge. If you
return defective parts, transportation charges must be prepaid by you. Vendor
will return replacement parts to original purchaser, freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties due
to accident, abuse, misuse, alteration, misapplication, improper installation or
improper maintenance or service by you or any third party, or failure to
perform normal and routine maintenance on the dispenser, as set out in the
User's Manual. In addition, the Limited Warranty does not cover damages to
the finish, such as scratches, dents, discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor
disclaims all warranties for products that are purchased from seller other than
authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR
EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER,
VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR
CONSEQUENTAL DAMAGES. Vendor assumes no responsibility for any defects
caused by third parties. This Limited Warranty gives the purchaser specific
legal rights; a purchaser may have other rights depending upon where he or
she lives. Some jurisdictions do not allow exclusion or limitation of special,
incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to you.
Primo Water Corporation
104 Cambridge Plaza Drive, Winston-Salem, NC 27104
www.PrimoWater.com
Changing Bottles
A flashing red function lights alerts you when your bottle is empty. Replace the
bottle as soon as possible.
Notice: Do not dispense hot, cool or cold water if the red light is flashing as
you could empty the tanks and cause the dispenser to overheat.
1. Open dispenser door and slide empty bottle out of cabinet.
2. Remove probe assembly from empty bottle. Place probe assembly on
probe hanger.
3. Set empty bottle aside.
4. Place fresh bottle outside of cabinet. Remove entire plastic cap from top of
bottle. Clean outside of new bottle with a cloth.
5. Place probe into bottle. Slide collar down until it clicks in place. Push head
down until tube hits bottom of bottle.
6. Slide bottle into cabinet and close door.
TROUBLESHOOTING
Cold water is not cold.
It takes up to one hour after setup to dispense cold water.
Make sure the power cord is properly connected to a working outlet.
Make sure the back of the dispenser is at least 4 inches from a wall and
there is free airflow on all 4 sides of the dispenser.
Make sure green switch on back of dispenser is ON.
If water still isn't cold, please call 866-429-7566 for assistance.
Hot water is not hot.
It takes 15-20 minutes after setup to dispense hot water.
Make sure the power cord is properly connected to a working outlet.
Make sure red switch on back of dispenser is ON.
Nightlight Isn't Working (Not on All Models)
Make sure the power cord is properly connected to a working outlet.
Make sure nightlight switch on back of dispenser is ON.
PN O-076D © 2012 Primo Water Corporation